Replace both parts and install the screws, impeller, nut and cover to finish the repair. Click to share on Twitter (Opens in new window), Click to share on Facebook (Opens in new window), Click to share on Pinterest (Opens in new window), Click to email this to a friend (Opens in new window), Click to share on LinkedIn (Opens in new window), Click to share on Reddit (Opens in new window), Click to share on Tumblr (Opens in new window). It is a Whirlpool Duet Steam. Washer Sud or SD Error – What It Means and How to Fix This Fault Code. All communications are opinions only and should not be considered a replacement for professional advice and/or service. How To Enter Service Mode On Whirlpool or Maytag Washer. It could also be telling you the load is too heavy or even that the pump is bad. If you can rotate the impeller while holding the inside tub still with your hand, then this might indicate that your drive hub needs replacing. Check the drain hose for kinks, plugs, twists, etc. Then run the washer on the largest load possible with no detergent and using hot water. Several pauses and rinse cycles might be added in order to completely remove the excessive suds. For the Whirlpool Duet, if you actually use too much detergent in your wash, you may find yourself looking at a SUDS LOCK error code. Required fields are marked *. Try to reset the Duet washer's memory by unplugging the washer for 2 minutes. Rinse or Spin mode does not work. The information on this site is intended for qualified service technicians and technically knowledgeable audience. Duet Washer User Interface Test (UI) Press the 1st button you used to enter the Duet Diagnostics Mode. Simply put, too much detergent was used and an excessive amount of suds or foam was produced. These signals indicate that the device cannot drain water with foam excess. Bookmark the permalink . – Your washer will then try to drain 4 for additional minutes. – Your Whirlpool washer will drain for 4 minutes then pause for 5 minutes. The device doesn’t drain water completely. Over time, the splines or fins on the inside part of the hub can wear down from use. now starting with drain lines. Then run the washer on the largest load possible with no detergent and using hot water. If you know you are using the proper amount and type of detergent for your washer, your machine might be due for a good cleaning. Select any three (3) buttons (except POWER) and follow the steps below, using the same buttons. We are on the honor system for our time, all I ask is please rate my service using the STAR RATING LINK on your page before you leave. Using too much detergent can cause more damage to the washing machine, which is why the SUDS code exists. In other words, the washer is taking too long to drain the water out of the tub. We live in a world where many believe that more is better. when a button is pressed the button’s indicator light should turn on and you should get a beep. Possible Causes / Procedure All communications are opinions only and should not be considered a replacement for professional advice and/or service. If you receive a “Sud” error, or “SD” fault code on your washer’s display, it means that there are far too many suds in your washer than what the machine can remove through a normal rinse cycle. Your email address will not be published. Remember the buttons and the order that the buttons were pressed. These days, for the sake of energy efficiency, washers don’t use enough water to cut through more than a tablespoon of detergent. To fix the SD error code, you might want to try anotherrinse cycle without the addition of moreb detergent. Run the washer through a cleaning cycle to remove any residual detergent that might have built up in the washer. I have revisited your post a few times now over the last year. If “Sud” is displayed a potential suds lock is detected. Post was not sent - check your email addresses! 4. Now that you are in the Duet washer interface test you can press each button one time. still getting f21 code here and there for no particular reason. Sometimes the machine will automatically detects this problem and add a pause and additional rinse cycle in order to break up the suds. 3. SUD SUD LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) The motor control unit senses a suds lock condition by analyzing the current draw on the drive motor. As the water level rises, the switch will cut off the water flow when the water level reaches a certain point in the tub. Check the sensor for the visible signs of damage, clean it. Thus you can clear al suds from your washer. High-Efficiency washers need to use specially-formulated HE detergent. cleaned out drain pump in past and has been nasty. First, you are using the incorrect detergent. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. Privacy Policy - Conditions of Use - Infringement Policy. Thank you for your inquiry. The Whirlpool washer gains too much or too little water needed for washing. The heating element starts to work because the device considers that the tank is full. Be careful! Contractor's Assistant: Can you guesstimate how old your Whirlpool is? “Sud “ or “SD”in display of your Whirlpool Washer. Sorry, your blog cannot share posts by email. If you don’t fix the damage time, it can lead to heating element burning and the danger of fire. And just to clarify, what's the exact model? Create a free website or blog at WordPress.com. It is most likely to be an overload of detergent or too much suds in the wash. It is about 4-5 years old. This entry was posted in Washing Machine Repair and Parts and tagged cabrio, code, Error, fault, not advancing, not spinning, SD, SUD, W10820039, washer, Washer Basket Drive Hub Kit, Whirlpool. The whole tub should spin along with the impeller. 5. This should rinse away the excess. To solve this SUDS issue, finish your current load, if possible. In this video, I help you fix a F21 error on a Whirlpool Duet Washer when it won't drain. I'm trying to find a solution to fix my washer. If you are not happy with the service please let me know before leaving a negative rating. This could be caused by using too much detergent or not using High Efficiency (HE) detergent. When "Sud" or "Sd" is displayed, the washer automatically extends the rinse time to remove the excess suds First of all, be sure the washer is in standby mode (plugged in with all indicators off). Some models display Sud, which is taken as 5ud. It helps prevent expensive calls to appliance repair. This means that the dispenser motor which directs fill water to the appropriate dispenser area, is not moving properly. If “Sud” is displayed a potential Suds Lock is detected. The control unit senses a suds lock condition by analyzing the current draw on the drive motor. Within 8 seconds, Whirlpool duet washer—flashes “sud” right after attempting to start cycle, but never enters the suds automatic routine. I get a suds and F35 code. This part can be replaced by removing the impeller cover and nut that holds the impeller in place. 2. Check the drain pump and drain hose for clogs and kinks to the drain hose. i will be back to see how i make out. Save my name, email, and website in this browser for the next time I comment. Previously, your washer could be dealing with this the best it could. • Check the drain hose and make sure it is not plugged or kinked, • Check Wire Harness connections to the Drain Pump, Pressure Switch, and Central Control Unit (CCU), • Check/ Clean Drain Pump Filter of foreign objects. If the washer is still having a problem you likely need a new main control board.